1. Plant
  2. Farm
  3. Process
  4. Trade
  5. Roast
  6. Brew
  7. Cup
Roasting · History

Industrial roasting history

How industrial coffee roasting changed after about 1920 – gas-fired drums with recirculated gas and burnt smoke, continuous and fluid-bed roasters, paddle and bowl designs, fast high-yield roasts and automatic control.

Across the chain: History · Equipment

Source-checkedby Coffearium verification pass· Last source-checked 16 Nov 2026· Prepared with AI assistance· 29 sources (4 tier A)· 1 contested· Updated 16 Nov 2026· Literature last searched 16 Nov 2026

In brief

  • US patents filed in 1933 and 1935 by Jabez Burns & Sons describe a drum heated by an external gas burner, with the gas recirculated and its smoke burnt.5,6
  • Continuous roasters roast without stopping between batches. The US roaster Hills Bros. Coffee patented one in 1969; a 1985 World Bank profile saw a trend towards them.11,15
  • Hot-air roasters without a turning drum followed: fluid beds (patents first filed 1953–1974), a paddle roaster (1968) and a rotating-bowl roaster (1971).13,14,16,18,20
  • Patents first filed in 1977–1983 claim roasts of minutes or seconds for low-density, high-yield coffee; a 2000 thesis reports that ultrafast roasting was later widely abandoned.10,22,24
  • Automatic control runs from a thermostat that ended the roast (patent filed 1932) to a colour sensor that stops it (patent filed 1998).4,28
Go to the deep dive ↓
Contents

Where this history begins#

History of roasting follows coffee roasting up to about 1920. By then, gas was already in use as a roasting fuel.1 A Burns patent of 1881 treats gas burners beneath a roasting drum as already known.1

This entry follows the machines of large roasting plants after that. It covers how the heat was made and led through the beans, how smoke was dealt with and how the roast was controlled. How the machines work in detail is explained in Drum roaster, Fluid-bed roaster and Tangential and centrifugal roasters.

Patents are the main evidence here. A patent shows who filed a design, when, and how it was built. It does not show whether the machine was sold or how well it roasted. Company histories and trade magazines are used only beside a patent or a book.

Gas-fired drums#

The patents of the 1920s and 1930s consulted here describe turning drums heated by gas.2,4,5 A US patent filed in 1928 places a gas burner along the centre of a revolving perforated drum.2 A patent of the American Coffee Corporation, Brooklyn, first filed in 1930, shows a gas burner heating the roaster.3

Gas let the hot combustion gases touch the beans.10 According to a 2000 doctoral thesis on hot-air roasting, this direct contact allowed much faster heat transfer.10 Other designs kept the flame away from the coffee. A US patent filed in 1949 heats a solid drum from outside: the combustion gases flow over its surface, not into it.7 Hot air circulates through the drum in a closed cycle, keeping the beans away from the products of combustion.7 This difference between direct and indirect heating is explained in Drum roaster.

Drums held the field for decades.9 According to a 2005 conference paper on the evolution of roasting, horizontal rotating drums were the only industrial batch roasters until the late 1950s.9 It describes a typical industrial batch system of the 1940s with recirculated gas and a water quench.9

Recirculated gas and burnt smoke#

A roaster sends hot gas and smoke into its exhaust.12 Leading part of that gas back to the heater saves heat; this is called recirculation.20 Patents of the roaster maker Jabez Burns & Sons of New York describe it in the 1930s.5,6

A Burns patent filed in 1933 passes gas heated by a flame through the coffee and then back to the flame.5 The flame burns the smoke particles before the gas is circulated again.5 The heater sits outside the roasting chamber.5 Excess gas is bled off.5

A Burns patent filed in 1935 shows the machine. A blower premixes gas and air for the burner in a separate heating chamber.6 A fan returns the gas from the drum to that chamber, through a separator for chaff.6 Most of the smoke is burnt in the heating chamber.6 The figure in the deep dive shows this air path.

Smoke could also be burnt separately. A Burns patent first filed in 1950 notes that the 1933 patent had a separate smoke burner in its bleeder pipe.8 Its own method burns the smoke in the roaster’s own combustion chamber instead.8 In 1985 a World Bank profile listed afterburners, wet scrubbing and thermal recovery for roaster smoke.11 By 1995 the US Environmental Protection Agency (EPA) described roaster off-gas as typically ducted to a thermal or catalytic oxidiser.12 These methods and the rules behind them are covered in Roaster emissions.

Continuous roasters#

A batch roaster roasts one charge at a time. A continuous roaster takes in green coffee and releases roasted coffee without stopping. According to the 2005 conference paper, continuous roasters were first used commercially in the 1940s.9 No patent of that decade was consulted for this entry.

The US roaster Hills Bros. Coffee filed a patent for a continuous roaster in 1969.15 A screw first carries the beans through a steam stage.15 They are then roasted on a vibrating plate, lifted by jets of hot gas.15 Most of the gas is recirculated to the jets.15

In 1985 the World Bank profile saw a trend from batch roasting towards large-scale continuous operations.11 According to the 2000 thesis, continuous roasters are generally designed for large hourly capacities.10 The EPA described roasters in 1995 as running in batch or continuous modes.12

Hot air without a turning drum#

From the 1950s, new designs moved the beans with air or with moving parts inside a fixed chamber.13,14,16 Fluid-bed roasters lift the beans in a stream of hot air. The Braunschweig firm Heimbs & Sohn filed such a process in Germany in 1953.13 The coffee is held aloft by gas flowing upwards; in one version the gas is cleaned, reheated and recycled.13 In a 1954 patent of Metallgesellschaft, Frankfurt, the roasting chamber has the shape of a Venturi tube.14

In 1974 Michael Sivetz of Oregon filed a patent for a roaster in which upward air keeps the beans circulating as a dense mass.20 It has batch and continuous versions and recycles part of the air.20 According to the 2005 conference paper, Neuhaus Neotec builds an industrial version.9

Two batch designs keep a fixed chamber or a turning bowl. The German machine maker Gothot filed a paddle roaster in 1968.16 Rotating vanes throw the beans in a fixed chamber, and hot gas enters tangentially at the bottom.16 The 2005 paper links this patent to the Gothot Rapido-Nova and the Probat RT roasters.9,17 Probat of Emmerich, Germany, filed a rotating-bowl roaster in 1971.18 The bowl throws the beans over its rim by centrifugal force.18

A US patent filed in 1990 spins a bed of beans in a fixed conical chamber with tangential hot air.21 The 2005 paper identifies it with the Burns System 90. It states that these newer batch roasters all recirculate gas and can roast very quickly.9

Fast roasts and high yields#

Soluble coffee plants percolate roasted and ground coffee through a battery of columns.11 A higher yield of soluble solids was one aim of faster roasting.22 US coffee companies patented faster roasts in the 1970s and 1980s.22,24,25

A Hills Bros. patent filed in 1977 claims a roast in two fluid-bed stages of about 5–10 minutes in total.22 It aims at a low-density product with a high yield of soluble solids.22 A Hills Bros. patent filed in 1980 describes a roast of about 3–4 minutes.23 A Procter & Gamble patent first filed in 1983 claims a roast of about 30–120 seconds in a fluid bed.24

Hotter, faster roasts puff the bean more. A 2000 laboratory study found greater bean volume and pore volume after high-temperature roasting than after low-temperature roasting.26 How roasting opens the cell structure is explained in Porosity and cell structure.

The trend reversed in part.10 According to the 2000 thesis, fast-roasted coffee caused packaging problems, more oil sweating and faster staling.10 High-yield coffees gave bitter, burnt and astringent brews.10 The thesis reports that ultrafast roasting was widely abandoned; a 2005 conference paper calls low-density roasting widely used (see Contested).9,10

Roasted coffee also had to be packed. Hills Brothers first offered vacuum-packed ground coffee in 1900, according to a university library exhibit.29 How tins, valves and brands developed is told in Brands and the industrial age and Packaging.

Automatic control#

Control came early.3,4 A patent first filed in 1930 roasts coffee at a continually rising temperature.3 A Burns patent filed in 1932 describes automatic batch roasting.4 A thermostat ends each roast at a set temperature, and a cam drum then times the following steps.4

Later systems watched the beans themselves.28 A US patent first filed in 1998 shines a laser through a window into the drum.28 A reflectometer reads the colour of the beans and stops the roast when the target is reached.28 According to the 2005 conference paper, several companies supplied roast controllers; one followed the bean-temperature record of control roasts.9 Profiles are explained in Roast profile.

Deep dive

Gas paths in industrial roasters#

The designs differ less in the vessel than in where the hot gas comes from and where it goes. Three questions sort them.

  • Direct or indirect. In direct firing the combustion gases pass through the beans; in indirect firing they heat the drum or the air from outside.7,10,12 The 2000 thesis links gas firing and direct contact to faster heat transfer and to fluid-bed roasters.10
  • Single pass or recirculated. The Burns patents of 1933 and 1935 send the gas back to the burner and bleed off only the excess.5,6 Patents of 1953, 1969 and 1974 also reuse the gas.13,15,20 A Probat patent of 1995 does not return the off-gas to the roaster; it recovers its heat.27 How recirculation changes the gas in the roaster is covered in Airflow.
  • Where the smoke burns. In the roaster’s own burner (1933, 1950) or in a separate burner or oxidiser after the roaster; the 1933 patent also has a smoke burner in its bleeder pipe.5,8,12 According to the EPA, separate oxidisers are more efficient, because they run 93–260 °C hotter than most roasters.12 A Probat patent first filed in 1995 burns the roaster off-gas and uses it, with the cooler air, for heat recovery.27
AB12345678
  1. Perforated drum. Turns and holds the batch; vanes lift the beans.6
  2. Premix burner. A blower mixes gas and air before the flame.6
  3. Heating chamber. Outside the roasting chamber; most of the smoke is burnt here.5,6
  4. Hot gas into the drum. Passes through the beans.5,6
  5. Chaff separator. In the return line.6
  6. Fan and damper. Return the gas to the heating chamber; the damper sets the flow.6
  7. Bleeder. Lets out the excess gas.5,6
  8. Separate oxidiser (B). In a later single-pass layout the off-gas leaves the roaster and is burnt in a thermal or catalytic oxidiser.12
A, the recirculating drum roaster of two Burns patents filed in 1933 and 1935; B, a single-pass roaster with a separate oxidiser, as described by the EPA in 1995. Arrows show the gas path. Schematic, not to scale.5,6,12

The patents name few operating values. The 1935 Burns patent states that its gas temperatures of 316–427 °C (source: 600–800 °F) are set through the flow of returning gas.6 The 1985 World Bank profile gives 5–20 min for the whole roasting operation.11

Reference dates#

Dates are the first filing (priority) and the grant of each patent, as printed or listed in the patent records.

First filed Design Record What the record shows Source
1928 Gas burner inside the drum US 1,716,920, A. P. Grohens; granted 11 Jun 1929 Burner along the centre of a revolving perforated drum 2
1930 Rising-temperature roast US 1,943,211, E. J. Dent, American Coffee Corporation; granted 9 Jan 1934 Continually rising temperature during the roast; gas burner 3
1932 Automatic batch roaster US 2,010,582, W. G. Burns and R. A. Greene, Jabez Burns and Sons; granted 6 Aug 1935 Thermostat ends the roast; cam drum times the cycle 4
1933 Recirculated gas, smoke burnt in the flame US 1,991,190, Backer, Keenan and Kopf, Jabez Burns and Sons; granted 12 Feb 1935 Gas passed through the coffee, back to the flame and round again 5
1935 Recirculating drum roaster US 2,081,349, same inventors; granted 25 May 1937 External heating chamber, fan, damper, chaff separator, bleeder 6
1949 Indirectly heated drum US 2,639,133, P. T. Clary; granted 19 May 1953 Combustion gases outside the drum; hot air in a closed cycle 7
1950 Smoke burnt in the roaster’s burner US 2,887,383, J. L. Kopf, Jabez Burns & Sons; granted 19 May 1959 Recirculation through the combustion chamber; water quench in the drum 8
1953 Coffee held aloft by gas US 2,859,116, E. Heimbs and W. Kangro, Heimbs & Sohn; granted 4 Nov 1958 Upward gas stream; in one version purified gas reheated and recycled 13
1954 Venturi-shaped fluid-bed roaster US 2,857,683, F. Schytil, Metallgesellschaft; granted 28 Oct 1958 Beans in suspension in hot air, little wall contact 14
1968 Paddle (tangential) roaster US 3,608,202, H. U. Arndt and P. Rossi, Gothot; granted 28 Sep 1971 Fixed chamber, rotating vanes, tangential hot-gas duct 16
1969 Continuous roaster US 3,572,235, L. Nutting et al., Hills Bros. Coffee; granted 23 Mar 1971 Steam stage, then gas jets on a vibrating plate; gas recirculated 15
1971 Rotating-bowl (centrifugal) roaster DE 21 03 281, H. Dege, Probat; laid open 17 Aug 1972 Beans thrown over the bowl rim; curved ribs under the lid 18
1973 Bowl with central air pipe DE 23 41 099, H. Dege et al., Probat; laid open 20 Feb 1975 Air pipe down the axis to the bowl floor; rotating cooling sieve 19
1974 Recirculating fluid bed US 3,964,175, M. Sivetz; granted 22 Jun 1976 Dense mass of beans circulated by upward air; batch and continuous 20
1977 Low-density, high-yield roast US 4,169,164, M. H. Hubbard et al., Hills Bros Coffee; granted 25 Sep 1979 Two fluid-bed stages, about 5–10 min in total (claimed) 22
1980 High-speed continuous roast US 4,322,447, M. R. Hubbard, Hills Bros. Coffee; granted 30 Mar 1982 Two chambers, about 3–4 min (described) 23
1982 Temperature-controlled density US 4,501,761, J. P. Mahlmann et al., General Foods; granted 26 Feb 1985 Gas at 200–240 °C for 2–10 min (claimed) 25
1983 Ultrafast roast US 4,988,590, S. E. Price et al., Procter & Gamble; granted 29 Jan 1991 Fluid bed, about 30–120 s (claimed) 24
1990 Spinning bed in a cone US 5,068,979, J. and D. R. Wireman, Blaw Knox; granted 3 Dec 1991 Fixed conical chamber, tangential hot air 21
1995 Heat recovery with off-gas burning US 5,718,164, H. Finken et al., Probat; granted 17 Feb 1998 Roasting and cooling air used for heat recovery 27
1998 Colour endpoint US 6,106,877, R. A. Allington et al., Fresh Roast Systems; granted 22 Aug 2000 Reflectometer through a drum window stops the roast 28
192019301940195019601970198019902000year first filed (priority)Gas burner inside aperforated drum19282 Continually rising roasttemperature19303 Automatic batch roaster,thermostat ends roast19324 Recirculated gas, smokeburnt in the flame(Burns)19335 Indirectly heated drum,closed air cycle19497 Smoke burnt in theroaster's own burner(Burns)19508 Coffee held aloft byupward gas195313 Venturi-shaped fluid-bedroaster195414 Paddle(tangential) roaster (Gothot)196816 Continuous roaster(Hills Bros.)196915 Rotating-bowl roaster(Probat)197118 Recirculating fluid bed(Sivetz)197420 Low-density, high-yieldroast(Hills Bros.)197722 Ultrafast roast, claimed30–120 s(Procter & Gamble)198324 Spinning bed in a cone199021 Off-gas burnt for heatrecovery(Probat)199527 Colour sensor stops theroast199828
Data table
Pointyear first filed (priority)Source
Gas burner inside a perforated drum192819282
Continually rising roast temperature193019303
Automatic batch roaster, thermostat ends roast193219324
Recirculated gas, smoke burnt in the flame (Burns)193319335
Indirectly heated drum, closed air cycle194919497
Smoke burnt in the roaster's own burner (Burns)195019508
Coffee held aloft by upward gas1953195313
Venturi-shaped fluid-bed roaster1954195414
Paddle (tangential) roaster (Gothot)1968196816
Continuous roaster (Hills Bros.)1969196915
Rotating-bowl roaster (Probat)1971197118
Recirculating fluid bed (Sivetz)1974197420
Low-density, high-yield roast (Hills Bros.)1977197722
Ultrafast roast, claimed 30–120 s (Procter & Gamble)1983198324
Spinning bed in a cone1990199021
Off-gas burnt for heat recovery (Probat)1995199527
Colour sensor stops the roast1998199828
Seventeen of the roasting patents consulted for this entry, by first filing (priority) year. Patents only; dates from secondary accounts are not shown.2,3,4,5,7,8,13,14,15,16,18,20,21,22,24,27,28

Roast times in patents and reports#

Roast times fell in the patents of the 1970s and 1980s. The figure shows the times the documents themselves state. They are process conditions claimed by the patent holders or reported by the World Bank, not measured comparisons.

02468101214161820minWorld Bank profile, wholeroasting operation(1985)5–20 min11 Hills Bros., two fluid-bedstages(filed 1977)5–10 min22 General Foods, gas at200–240 °C(filed 1982)2–10 min25 Hills Bros., high-speedcontinuous(filed 1980)about 3–4 min23 Procter & Gamble,ultrafast fluid bed(first filed 1983)about 30–120 s24
Data table
minSource
World Bank profile, whole roasting operation (1985)5–20 min11
Hills Bros., two fluid-bed stages (filed 1977)5–10 min22
General Foods, gas at 200–240 °C (filed 1982)2–10 min25
Hills Bros., high-speed continuous (filed 1980)about 3–4 min23
Procter & Gamble, ultrafast fluid bed (first filed 1983)about 30–120 s24
Roasting times stated in a 1985 World Bank profile and in four US roasting patents first filed in 1977–1983. Claimed process conditions, not measurements.11,22,23,24,25

The patents tie short times to lower density. The 1977 Hills Bros. patent claims a tapped bulk density below about 0.39 g/cm³.22 The 1982 General Foods patent sets density through the gas temperature and the time.25 The 2000 pore-structure study supports the direction of the effect: high-temperature roasting gave greater bean and pore volume at the same roast degree.26 Its abstract gives no density values.

The 2000 thesis lists the drawbacks that followed. Greater volume and more gas made packing harder.10 Fast-roasted coffee showed more oil on the surface and staled faster in storage.10 High-yield coffees gave bitter, burnt and astringent brews, according to the sources it reviews.10

Documented, claimed and retold#

Coffearium sorts dates as in History of roasting. Documented means a patent or an official report: all dates in the table above, the World Bank profile of 1985 and the EPA document of 1995.11,12

Claimed means a date given by one secondary account. The 2005 conference paper dates the first commercial continuous roasters to the 1940s.9 It states that the Lurgi Aerotherm, a deep fluid-bed roaster, was introduced in 1957 and is no longer marketed.9 None of the patents consulted names the Aerotherm. The paper also says drums were the only industrial batch roasters until the late 1950s.9

Retold means a story repeated without a primary source. No date in this entry rests on such a story. A trade magazine traces the paddle roaster to a Gothot patent of 1969; the Gothot patent was filed in the United States in 1969, with a German priority of 1968.16,17

Machine names come from secondary sources. The 2005 conference paper links patents to the Gothot Rapido-Nova, Probat RT, Probat RZ, Neuhaus Neotec RFB and Burns System 90.9 None of the patents consulted names a commercial model.

Open questions#

  • Continuous roasting since 1985. The World Bank saw a trend towards continuous roasting in 1985.11 No source consulted for this entry gives the share of coffee roasted continuously in any year.
  • The first commercial continuous roaster. The 1940s date rests on one conference paper.9 No patent or company record of the 1940s was consulted.
  • European patents before 1950. German roaster patents of the years between the wars were not consulted. The US record may overstate the role of US makers (our note).
  • When afterburners spread. No source consulted for this entry dates the first separate afterburner on a coffee roaster, or says how common afterburners were before 1985.
  • High-yield roasting after 2000. Whether fast, low-density roasting is still widely used by large roasters is disputed (see Contested).9,10

Key studies#

Backer, Keenan and Kopf, 1935 – Roasting method (US 1,991,190). Gas heated by a flame outside the drum passes through the coffee and back to the flame, which burns the smoke before the gas circulates again. Excess gas is bled off. An early documented recirculating roaster.

Jabez Burns and Sons; filed 23 Mar 1933, granted 12 Feb 1935 · US 1,991,190

Nutting et al., 1971 – Continuous coffee roasting apparatus (US 3,572,235). Beans pass a steam stage on a screw, then roast continuously on a vibrating plate, lifted by jets of hot gas. Most of the gas returns to the jets.

Hills Bros. Coffee; filed 1 Apr 1969, granted 23 Mar 1971 · US 3,572,235

Arndt and Rossi, 1971 – Device for batch roasting and cooling particulate material (US 3,608,202). A fixed chamber with a curved bottom, rotating vanes that throw the beans, and a hot-gas duct tangential to the bottom. The earliest paddle-roaster patent consulted.

Maschinenfabrik Ferd. Gothot; German priority 7 Mar 1968, granted 28 Sep 1971 · US 3,608,202

Dege, 1971 – Einrichtung zur Wärme-, Kälte- und/oder Stoffbehandlung (DE 21 03 281). A turning vessel throws coffee or cocoa over its rim by centrifugal force; with curved ribs on the underside of the lid. The first Probat rotating-bowl patent consulted.

Probat-Werke von Gimborn; filed 25 Jan 1971 · DE 21 03 281

Schenker, 2000 – Investigations on the hot air roasting of coffee beans. A doctoral thesis whose review traces the trend to ultrafast roasting in the 1970s and 1980s, its claimed benefits for density and yield, and the packaging, staling and flavour problems that led to its abandonment.

Diss. ETH No. 13620, ETH Zürich · PDF

Contested
  • Fast, high-yield roasting around 2000: a 2000 doctoral thesis reports that ultrafast roasting had been widely abandoned in industrial practice in recent years and that roasts of several minutes were common again10; a 2005 conference paper states that low-density, high-yield roasting is now widely used by large-scale roasters, and points to the lighter fill of coffee cans.9 The two may describe different things: the thesis writes about the shortest roasts, the paper about low-density roasting in general. No industry survey was consulted.
Share or cite this entry

Change log

  • – Heimbs & Sohn patent: the gas is cleaned, reheated and recycled only in one version (text, table, timeline label). Reason: The patent's first embodiment uses fresh air; only the Fig. 5 version recycles purified gas.
  • – The 1995 Probat patent no longer listed among patents that reuse the roasting gas; it recovers the heat of the burnt off-gas. Reason: The patent heats the cooling air indirectly and feeds it to the roaster; it departs from recirculating the roasting gas.
  • – The separate smoke burner in the bleeder pipe is attributed to the 1933 Burns patent, as the 1950 patent states. Reason: US 2,887,383 names US 1,991,190 as the patent with that burner.
  • – Roast times from patents worded as claimed or described conditions (text, quick facts, table, timeline label); brief no longer implies Hills Bros. patented the first continuous roaster; controller sentence narrowed to what the 2005 paper says; contested item dated around 2000 with each side's context. Reason: Patents are A only for construction and dates; the 2005 paper names one profile-following controller; the thesis speaks of the years before 2000.
  • – Six stored quotes corrected to the exact wording (s2, s7, s11, s15, s21, s27); Fig. 1 caption passages of the 2005 paper added for the 1940s system with recirculated gas and a water quench. Reason: Checked by hand against Google Patents, the World Bank PDF and the conference paper.

Sources

  1. A/BBurns, J. (assignor to Durbrow, W.) (1881). Coffee-roaster (US Patent 241,295). United States Patent Office; filed 21 October 1880, granted 10 May 1881.Quoted passage: a description; Patent specification of a gas-heated drum roaster, Brooklyn, New York; used here only for the hand-over from History of roasting..
  2. A/BGrohens, A. P. (1929). Burner for roasters (US Patent 1,716,920). United States Patent Office; filed 10 September 1928, granted 11 June 1929.Quoted passage: a description; Patent specification of a gas burner mounted along the centre of a revolving perforated roasting drum..
  3. A/BDent, E. J. (assignor to American Coffee Corporation) (1934). Method for roasting coffee (US Patent 1,943,211). United States Patent Office; filed 20 January 1931 (division of an application filed 1 April 1930), granted 9 January 1934.Quoted passage: a description; Patent for a roasting method with a continually rising temperature during the roast; American Coffee Corporation, Brooklyn, New York..
  4. A/BBurns, W. G.; Greene, R. A. (assignors to Jabez Burns and Sons) (1935). Automatic roaster and cooler (US Patent 2,010,582). United States Patent Office; filed 18 June 1932, granted 6 August 1935.Quoted passage: a description; Patent specification of a drum roaster and cooler in which a thermostat ends the roast and a cam drum times the following steps; Jabez Burns and Sons, New York..
  5. A/BBacker, L. H.; Keenan, J. H.; Kopf, J. L. (assignors to Jabez Burns and Sons) (1935). Roasting method (US Patent 1,991,190). United States Patent Office; filed 23 March 1933, granted 12 February 1935.Quoted passage: a description; Patent for a batch roasting method in which burner gases pass through the coffee, return to the flame and are recirculated; Jabez Burns and Sons, New York..
  6. A/BBacker, L. H.; Keenan, J. H.; Kopf, J. L. (assignors to Jabez Burns & Sons) (1937). Roasting apparatus (US Patent 2,081,349). United States Patent Office; filed 8 February 1935 (continuation in part of the application filed 23 March 1933), granted 25 May 1937.Quoted passage: a description; Patent specification of a recirculating drum roaster: external heating chamber, fan and return pipe, damper, chaff separator and bleeder; Jabez Burns & Sons, New York..
  7. A/BClary, P. T. (1953). Coffee roaster (US Patent 2,639,133). United States Patent Office; filed 26 August 1949, granted 19 May 1953.Quoted passage: a description; Patent specification of a batch drum roaster heated from outside by a gas burner, with hot air circulated in a closed cycle; Carnegie, Pennsylvania..
  8. A/BKopf, J. L. (assignor to Jabez Burns & Sons) (1959). Method of roasting (US Patent 2,887,383). United States Patent Office; filed 25 May 1956 (division of an application filed 18 August 1950), granted 19 May 1959.Quoted passage: a description; Patent for a recirculating batch roasting method in which smoke is burnt in the roaster's own combustion chamber; Jabez Burns & Sons, New York..
  9. BSchwartzberg, H. G. (2005). Evolution of Coffee Roasting (paper 600b). AIChE Annual Meeting 2005, Food Process and Product Development – Case Histories (conference proceedings).Quoted passage: a description; Review of roaster designs, heat transfer, gas recirculation, pollution control and fast roasting, written in 2005 with references to patents..
  10. BSchenker, S. (2000). Investigations on the Hot Air Roasting of Coffee Beans (Diss. ETH No. 13620). ETH Zürich (doctoral thesis).Quoted passage: a description; Doctoral thesis on hot-air roasting; the literature review (section 2.2.2) summarises roaster types and the rise and decline of ultrafast roasting..
  11. AWorld Bank, Finance and Agro-Industry Unit (1985). Agro-Industry Profiles: Coffee. World Bank.Quoted passage: a description; World Bank profile of the coffee processing industry for investment appraisal, October 1985; roasting, soluble coffee, packing and environmental aspects..
  12. AU.S. Environmental Protection Agency (1995). AP-42, Fifth Edition, Section 9.13.2: Coffee Roasting. U.S. EPA, Compilation of Air Pollutant Emission Factors.Quoted passage: a description; US federal emission-factor document for coffee roasting plants: process description, emissions and controls, as of 1995..
  13. A/BHeimbs, E.; Kangro, W. (assignors to Heimbs & Sohn) (1958). Treatment of coffee and other materials (US Patent 2,859,116). United States Patent Office; German priority 13 June 1953, filed 7 June 1954, granted 4 November 1958.Quoted passage: a description; Patent for roasting coffee held aloft in an upward gas stream, with surfaces no hotter than the roasting temperature; Heimbs & Sohn, Braunschweig, Germany..
  14. A/BSchytil, F. (assignor to Metallgesellschaft AG) (1958). Coffee roaster (US Patent 2,857,683). United States Patent Office; filed 10 May 1954, granted 28 October 1958.Quoted passage: a description; Patent specification of a coffee roaster in which the beans are kept in suspension in hot air in a Venturi-shaped chamber; Metallgesellschaft, Frankfurt am Main..
  15. A/BNutting, L.; Chong, G. S.; Miller, J. T.; McChesney, J. G. (assignors to Hills Bros. Coffee) (1971). Continuous coffee roasting apparatus (US Patent 3,572,235). United States Patent Office; filed 1 April 1969, granted 23 March 1971.Quoted passage: a description; Patent specification of a continuous roaster with a steam stage and a bed of beans fluidised by hot-gas jets on a vibrating plate; Hills Bros. Coffee..
  16. A/BArndt, H. U.; Rossi, P. (assignors to Maschinenfabrik Ferd. Gothot) (1971). Device for batch roasting and cooling particulate material (US Patent 3,608,202). United States Patent Office; German priority 7 March 1968, filed 7 March 1969, granted 28 September 1971.Quoted passage: a description; Patent specification of a batch roaster with a fixed chamber, rotating vanes and a tangential hot-gas inlet; Maschinenfabrik Ferd. Gothot, Mülheim (Ruhr), Germany..
  17. CGlobal Coffee Report (staff writer) (2014). Probat on innovation's origin. Global Coffee Report.Quoted passage: a description; Trade-press article on the origin of the tangential (paddle) roaster, from the Gothot system to Probat's later lines..
  18. A/BDege, H. (Probat-Werke von Gimborn Maschinenfabrik) (1971). Einrichtung zur Wärme-, Kälte- und/oder Stoffbehandlung (German Patent DE 21 03 281). Deutsches Patentamt; filed 25 January 1971, laid open 17 August 1972 (DE 21 03 281 A1), granted 10 September 1981 (C3).Quoted passage: a description; German patent of Probat, Emmerich, for a rotating vessel that throws the material over its rim by centrifugal force, with curved ribs under the lid; for roasting coffee or cocoa..
  19. A/BDege, H.; Jansen, G.; Schabbel, R. (Probat-Werke von Gimborn Maschinenfabrik) (1973). Einrichtung zur Wärme-, Kälte- und/oder Stoffbehandlung (German Patent DE 23 41 099). Deutsches Patentamt; filed 14 August 1973, laid open 20 February 1975 (A1), granted 23 September 1982 (C2).Quoted passage: a description; German patent of Probat for a rotating bowl with a central air pipe reaching down towards its floor and an annular rotating cooling sieve; for roasting coffee or cocoa..
  20. A/BSivetz, M. (1976). Coffee roasting system (US Patent 3,964,175). United States Patent and Trademark Office.Quoted passage: a description; Patent of a hot-air roaster in which an upward air stream keeps the beans circulating as a dense mass; batch and continuous versions; Corvallis, Oregon..
  21. A/BWireman, J.; Wireman, D. R. (assignors to Blaw Knox Food and Chemical Equipment Co.) (1991). Apparatus for conditioning particulate material (US Patent 5,068,979). United States Patent and Trademark Office; filed 11 January 1990, granted 3 December 1991.Quoted passage: a description; Patent specification of a stationary conical roasting chamber in which tangentially injected hot air spins a bed of coffee beans..
  22. A/BHubbard, M. H.; Phipps, R. R.; Thompson, R. L. (assignors to Hills Bros Coffee) (1979). Low density coffee roasting process (US Patent 4,169,164). United States Patent and Trademark Office; filed 23 December 1977, granted 25 September 1979.Quoted passage: a description; Patent for two-stage continuous fluidised-bed roasting to a low-density, high-yield product; Hills Bros Coffee..
  23. A/BHubbard, M. R. (assignor to Hills Bros. Coffee) (1982). High speed process for roasting coffee (US Patent 4,322,447). United States Patent and Trademark Office; filed 29 September 1980, granted 30 March 1982.Quoted passage: a description; Patent for continuous two-chamber roasting in a shallow vibrated, fluidised bed; Hills Bros. Coffee..
  24. A/BPrice, S. E.; Kussin, R. F.; Fruhling, R. J.; Harris, M. B. (assignors to Procter & Gamble) (1991). Ultrafast roasted coffee (US Patent 4,988,590). United States Patent and Trademark Office; priority 22 July 1983, filed 21 October 1985, granted 29 January 1991.Quoted passage: a description; Patent for coffee roasted in a fluidised bed within seconds; Procter & Gamble..
  25. A/BMahlmann, J. P.; Schecter, S. M.; Scher, L. (assignors to General Foods) (1985). Controlled coffee roasting (US Patent 4,501,761). United States Patent and Trademark Office; filed 12 October 1982, granted 26 February 1985.Quoted passage: a description; Patent for roasting in a gas held at a set temperature to control bean density; General Foods..
  26. ASchenker, S.; Handschin, S.; Frey, B.; Perren, R.; Escher, F. (2000). Pore structure of coffee beans affected by roasting conditions. Journal of Food Science 65(3), 452–457. doi:10.1111/j.1365-2621.2000.tb16026.x · other copiesQuoted passage: the authors’ own result; Laboratory hot-air roasting of one coffee by two time–temperature processes to the same roast degree; volumetry, mercury porosimetry and electron microscopy..
  27. A/BFinken, H.; Jansen, G.; Naves, E. (assignors to Probat-Werke von Gimborn Maschinenfabrik) (1998). Arrangement for roasting vegetable bulk material, such as coffee beans (US Patent 5,718,164). United States Patent and Trademark Office; German priority 1 June 1995, filed 31 May 1996, granted 17 February 1998.Quoted passage: a description; Patent specification of a roasting plant that burns the roaster off-gas and recovers heat from it and from the cooler air; Probat, Emmerich..
  28. A/BAllington, R. A.; Torbet, P. A.; Granger, E. M. (assignors to Fresh Roast Systems) (2000). Method of terminating roasting of bulk materials in real time on basis of objectively determined color of materials (US Patent 6,106,877). United States Patent and Trademark Office; priority 1 May 1998, filed 29 April 1999, granted 22 August 2000.Quoted passage: a description; Patent specification of a reflectometer that reads the colour of the beans through a window in the drum and stops the roast..
  29. AUC Davis Library (curated by A. Russek) (2025). The First Wave of Coffee (exhibit Brewed Awakening: The Evolution of the Coffee Industry). University of California, Davis, Library; exhibit in the Shields Library, 28 October 2025–1 April 2026.Quoted passage: a description; University library exhibit on US commodity coffee brands, late 19th to mid-20th century..

Tier A · authoritative · B · trade and expert · C · general. Supporting quotes for every source are in the data version of this entry. If a publisher’s site refuses access, try the doi link or “other copies”.

The literature for this entry was last searched on 16 Nov 2026. A statement that no source consulted for this entry shows something refers to the sources above; newer or missing work may exist.

Suggest a change

On Industrial roasting history. Tell us what you would change and why. A source that supports it helps most.