1. Plant
  2. Farm
  3. Process
  4. Trade
  5. Roast
  6. Brew
  7. Cup
Trade · Rule

Green coffee quality control

How exporters, importers and roasters check green coffee lots – when samples are tested, the test panel from moisture to cupping, food-safety screening, accepting or claiming against the contract, records and instrument checks.

Source-checkedby Coffearium verification pass· Last source-checked 10 Nov 2026· Prepared with AI assistance· 23 sources (18 tier A)· Updated 16 Nov 2026· Literature last searched 10 Nov 2026

In brief

  • The sampling standard for bagged green coffee, ISO 4072, names quality control and quality inspection among the purposes for which samples are drawn.2
  • Moisture is measured by the ISO 6673 oven method (about 10 g at 105 °C for 16 h) or by meters calibrated against it; ISO 24115 sets the calibration procedure.4,6,11
  • In the interlaboratory test of the ISO 6673 oven method, the reproducibility limit between laboratories was 0.54–1.19 percentage points across five green coffee samples.4
  • The EU sets maximum levels of ochratoxin A for roasted and soluble coffee but none for green coffee.18
  • Under the 2018 European Standard Contract for Coffee (ESCC), a quality difference established by arbitration entitles the buyer to an allowance, a reduction in price.15
Go to the deep dive ↓
Contents

What quality control does#

Green coffee changes hands several times between the dry mill and the roaster. At each step someone checks it. A lot is a batch of coffee from one origin and process, traded as a unit. Quality control (QC) asks three questions about it: does it match what was sold, is it safe, and will it keep?

The checks work on samples, not on the whole lot.2 The sampling standard for bagged green coffee, ISO 4072, names quality control and quality inspection among the purposes of a sample.2 According to the International Trade Centre (ITC), quality is judged by the green appearance, the roast appearance and the cup.23

The yardstick is the contract. A lot is sold on a description, a sample or an agreed type; Samples in the trade explains these. The grades and defect tables the checks refer to are explained in Green coffee grading standards. This entry describes the system that applies them: when, how and with what instruments.

When coffee is checked#

The same lot is checked at several points. The figure follows one lot from the offer to the roaster.

12345
  1. Offer. The buyer grades and cups a sample of what is on offer.2,23
  2. Before shipment. The exporter checks that the lot is evenly dried, below 12.5% moisture and within defect limits.1,14
  3. Arrival. Samples drawn after discharge are compared with the contract; the claim period starts.15,16
  4. Storage. Moisture and condition of stored lots are re-checked; records note each lot’s condition and age.1,7
  5. Before roasting. Moisture must still be within 12.5%; a cupping can decide acceptance if the parties agree.1,13
Quality control checkpoints for one lot of green coffee, from offer to roaster. Schematic, not to scale.1,2,15,16

Offer and pre-shipment. According to an FAO manual, internationally traded coffee is normally sold after the buyer has received a representative sample.2 Exporters also check their own lots before loading. The Codex code of practice on ochratoxin A asks that lots be uniformly dried, below 12.5% moisture and within defect limits before shipment.1 A 2004 resolution of the International Coffee Organization (ICO) sets moisture and defect targets for exports.14 The certificate of origin of each shipment shows whether it meets them.14

Arrival. The buyer compares samples of the delivered coffee with the contract or approved sample. The contracts set short time limits for this (see “Accept, claim or reject” below).15,16

Storage and roasting. Coffee can change in the warehouse, so stored lots are checked again.7 The Codex code asks warehouses to record the condition and age of the stock they receive.1 Its moisture ceiling of 12.5% applies until the coffee is roasted.1

The test panel#

A QC laboratory runs a short list of tests on each sample. Most have an international method. The values that define a grade are in Green coffee grading standards; the methods are summarised here.

  • Moisture. The reference is the oven method ISO 6673. About 10 g of beans are heated at 105 °C for 16 hours, and the loss in mass is weighed.4 Day to day, laboratories use electronic meters calibrated against it.11
  • Water activity. Instruments measure it on a scale from 0 to 1.8 The Codex code ties a low value, with low moisture, to protection from fungi.1
  • Density and size. Bulk density is the mass of beans that fills a known volume.9 Screen size is measured with sieves; see Bean size and density.
  • Defects, colour and odour. A grader counts defective beans on a fixed sample, compares its colour with a chart and smells it for foreign or mouldy odours.10,11,23
  • Sample roast and cupping. A small batch is roasted to a set degree and tasted in several cups.12

Food-safety tests are added where a risk is known. They look for ochratoxin A, a mould toxin, and for pesticide residues.1,20

Accept, claim or reject#

The result of QC is a decision. Most often the green coffee matches and is accepted. If it does not, the contract decides what happens.

Under the 2018 European Standard Contract for Coffee (ESCC), the buyer has 28 calendar days from final discharge to make a quality claim.15 A quality difference established by arbitration gives the buyer an allowance, a reduction in price that may include costs.15 Only coffee that is unsound, or radically different, can be invoiced back to the seller. Excessive moisture is one sign of unsound coffee.15

The contract of the Green Coffee Association (GCA) has a shorter window for shipment terms.16 Coffee counts as accepted unless, within 15 calendar days of discharge, a claim is settled or arbitration samples are ordered.16 Quality is then a matter of allowance only, unless the contract provides otherwise.16 Arbitration explains how the samples are judged.

Records and lot identity#

A test result is only useful if it can be tied to the right lot. The Codex code asks warehouses to keep coffee types apart with a labelling system.1 According to the ITC guide, the quality system ISO 9001 gives processors identification and traceability for their coffee.23

Records also show that the checks were done. Under EU food hygiene law, businesses after primary production keep documents and records that fit the nature and size of the business.21 How lots are traced along the whole chain is covered in Traceability.

Deep dive

Reference values#

Parameter Value Source
Sampling of bagged lots (ISO 4072) At least 10 bags in lots of 10–100 bags, at least 10% above 100; increments 30 ± 6 g, preferably 3 points per bag; bulk sample ≥ 1,500 g; laboratory sample ≥ 300 g ISO 4072 as reproduced by FAO2
Moisture, reference method ISO 6673: ≈10 g test portion, oven with forced ventilation at 105 ± 1 °C, 16 h ± 0.5 h, two determinations, result = mean ISO 6673:20034
ISO 6673 precision (5 samples, 8.50–11.40%) Repeatability limit r 0.11–0.34; reproducibility limit R 0.54–1.19 (percentage points) ISO 6673:2003, Table 14
Meter calibration (ISO 24115) ≥ 5 reference samples; validated range 8.5–13.5%; ≥ 3 readings per reference sample; ambient temperature, 40–70% RH ISO 241156
Meter readings per sample 3–5 replicates SCA CVA11
Meter calibration interval Once a year before harvest (Codex); at the start of each season (ITC) Codex1, ITC23
Same coffee, two methods (2005 container trial) Oven 10.25–10.55%; capacitance meter 12.26–12.70% (basis not stated) ITAL report17
Moisture limits ≤ 12.5% (wb) from loading to roasting (Codex); 8–12.5% by ISO 6673 (ICO export target) Codex1, ICO14
Water activity ≤ 0.67–0.70 with < 12.5% moisture (wb) protects parchment coffee (Codex); not a required test in the SCA CVA Codex1, SCA11
Water activity method ISO 18787: range 0–1; dew point, electrolyte or polymer sensor ISO8
Defect limits (ICO export target) ≤ 86 defects per 300 g (arabica); ≤ 150 per 300 g (robusta) ICO14
Physical sample (SCA CVA) 350 g for defects and colour SCA11
Sample roast “Medium”: ground coffee L* 26–29, Agtron “Gourmet” 63; air-cooled; rest 8–24 h SCA 102-202412
Cupping 8.25 g per 150 mL; 5 cups per sample (affective assessment) SCA 102-202412
Ochratoxin A, EU maximum None for green coffee; 3.0 µg/kg roasted beans and ground roasted coffee; 5.0 µg/kg soluble coffee Reg. (EU) 2023/91518
Ochratoxin A, standard method EN 14132, validated for roasted coffee 0.2–5.5 µg/kg EN 1413219
Quality claim windows 28 calendar days from final discharge (ESCC); 15 calendar days after discharge (GCA shipment terms) ESCC15, GCA16

Moisture values are mass fractions as each document gives them; the ISO standards use loss in mass by ISO 6673. Ranges for ISO 6673 are the lowest and highest values across its five samples.

Sampling and representativeness#

A test is only as good as the sample. ISO 4072 has sampling done by experienced or trained samplers.2 It takes increments from at least 10 bags, or 10% of the bags above 100, preferably at three points in each bag.2 The increments are combined into a bulk sample of at least 1,500 g, from which laboratory samples of at least 300 g are taken.2 A bag trier to ISO 6666 takes beans through the side of a closed bag.3

Moisture samples need their own packing. ISO 4072 puts them in moisture-proof containers with airtight closures, so they cannot dry or take up water before the test.2 Bulk sampling, sample sizes in the contracts and sample retention are covered in Samples in the trade.

Moisture: reference method and meters#

The oven method. ISO 6673 heats a test portion of about 10 g at 105 ± 1 °C for 16 h ± 0.5 h, in an oven with forced ventilation.4 Two determinations are made on the same sample, and the result is their mean.4 The 2003 edition was replaced in November 2025 by a third edition that covers decaffeinated and non-decaffeinated green coffee.5 Whether its parameters changed could not be checked for this entry.

Precision of the oven. In an international interlaboratory test of ISO 6673, 14 laboratories took part and 13 were retained.4 Across five samples of 8.50–11.40% moisture, the repeatability limit r, for results within one laboratory, was 0.11–0.34 percentage points.4 The reproducibility limit R, for results from different laboratories, was 0.54–1.19 percentage points.4 A buyer and a seller who both follow the method can therefore differ by up to about one point (our inference).

Meters. The most used moisture meters for coffee are adapted grain meters that measure capacitance.7 Modern units also measure temperature and bulk density, because both change the electrical reading.7 Every electronic meter drifts; calibration against the oven method corrects the drift.7 Calibration cannot correct poor repeatability, and a meter that needs frequent recalibration should be repaired or replaced.7 Averaging several readings of the same sample makes a meter more precise.7 The SCA’s Coffee Value Assessment (CVA) asks for 3–5 replicate readings with a meter calibrated against ISO 6673.11 Hot samples are cooled to ambient temperature first, unless the meter is rated for them.7

Calibration procedure. ISO 24115 sets out how to adjust and calibrate a meter for green coffee.6 At least five reference samples are prepared at different moisture levels, and their moisture is assigned by ISO 6673.6 The validated range is 8.5–13.5%.6 Each reference sample is read at least three times, at ambient temperature and 40–70% relative humidity.6 The calibration curve relates meter readings to the reference values; a linear regression is usually suitable.6 A correction term for bean temperature is worked out, and the result is reported with an expanded uncertainty for each moisture point, generally with a coverage factor k = 2 for 95%.6

00.511.522.5percentage pointsISO 6673 oven,repeatability limit r(one laboratory; 5 samples)0.11–0.344 ISO 6673 oven,reproducibility limit R(13 laboratories; 5 samples)0.54–1.194 Capacitance meter minusoven, same coffee(2005 trial; our calculation)1.95–2.1517
Data table
percentage pointsSource
ISO 6673 oven, repeatability limit r (one laboratory; 5 samples)0.11–0.344
ISO 6673 oven, reproducibility limit R (13 laboratories; 5 samples)0.54–1.194
Capacitance meter minus oven, same coffee (2005 trial; our calculation)1.95–2.1517
Spreads in moisture measurement of green coffee, in percentage points. The bars are different statistics: r and R are limits for the difference between two results; the last row is a systematic offset, our calculation from the layer means of the trial.4,17

When methods disagree. A 2005 Brazilian government laboratory report for an FAO project measured the same hulled arabica three ways during simulated sea transport.17 In the full container, the oven gave 10.25–10.55% and a capacitance meter 12.26–12.70% (basis not stated).17 Across the three layers, the oven read 10.25–10.33% at the start and 10.39–10.55% at the end; the meter read 12.26–12.30% and 12.51–12.70%.17 The meter was 1.95–2.15 points higher in every layer and at both times (our calculation from the layer means).17 The authors put the gain by either method at less than 0.3%.17 By layer, the full container’s means give gains of 0.08–0.30 points by oven and 0.22–0.40 by meter (our calculation).17 A third method, weight gain, went from 10.31–10.43% to 11.07–11.85%, and the authors took it as the measure of moisture uptake.17 An offset of this kind is what calibration against ISO 6673 removes.6,7 Without it, a lot at 10.5% could read above the 12.5% Codex ceiling (our inference).1,17

1010.51111.51212.513% moisture (basis not stated)Oven, ISO 6673 – start10.25–10.3317 Oven, ISO 6673 – end10.39–10.5517 Capacitance meter – start12.26–12.3017 Capacitance meter – end12.51–12.7017 Weight gain – start10.31–10.4317 Weight gain – end11.07–11.8517
Data table
Point% moisture (basis not stated)Source
Oven, ISO 6673 – start10.25–10.3310.25–10.3317
Oven, ISO 6673 – end10.39–10.5510.39–10.5517
Capacitance meter – start12.26–12.3012.26–12.317
Capacitance meter – end12.51–12.7012.51–12.717
Weight gain – start10.31–10.4310.31–10.4317
Weight gain – end11.07–11.8511.07–11.8517
Moisture of the same hulled arabica in the full container of a 2005 simulated-transport trial, by method, at the start and end; spans cover the lower, middle and upper layers (means of three 15-day trials; basis not stated).17

Water activity, density, size, colour and odour#

Water activity. ISO 18787 covers water activity in foods across the range 0 to 1.8 Its instruments work by dew point, by the conductivity of an electrolyte or by the permittivity of a polymer.8 The Codex code considers parchment coffee protected from fungi at a water activity of at most 0.67–0.70 together with less than 12.5% moisture (wet basis).1 The SCA CVA does not require the test.11 Thresholds and isotherms are explained in Moisture and water activity.

Density and size. ISO 6669 defines bulk density as the ratio of mass to the volume occupied, measured on free-flowing whole beans.9 According to the standard, botanical, processing, storage and handling factors, including age, influence it.9 No numeric acceptance limit for density was found in the standards consulted for this entry. Size analysis by sieving is described in Bean size and density.

Defects, colour and odour. ISO 4149 specifies the olfactory and visual examination of green coffee and the determination of foreign matter and defects; its third edition appeared in November 2025.10 The CVA counts defects and judges colour on a 350 g sample.11 According to the ITC guide, a careful look and a check for mouldy or earthy smells help to detect mould.23 Defect types and their counting are in Green coffee grading standards and Green coffee defects and their causes.

Sample roast and cupping#

The cup decides many acceptances. ISO 6668 describes how green coffee samples are prepared for sensory analysis. Its scope states that the result may decide acceptance or rejection of a shipment, if the parties agree.13 According to the ITC guide, the taster’s first aim is to decide whether a coffee is acceptable for its type and standard.23

SCA Standard 102-2024 fixes the sample roast at a “medium” degree, defined as a ground-coffee lightness L* of 26–29 or 63 on the Agtron “Gourmet” scale.12 The sample is air-cooled without water and rests 8–24 hours.12 Batches outside the target roast are not cupped; the roast is repeated.12 The dose is 8.25 g per 150 mL of cup volume, and five cups per sample are tasted in the affective assessment.12 The CVA keeps physical results from the tasters until the sensory work is finished.11 The full protocol is in Cupping; roast quality control is outside this entry.

Food-safety screening#

Ochratoxin A. The EU sets maximum levels of 3.0 µg/kg for roasted beans and ground roasted coffee and 5.0 µg/kg for soluble coffee. No level names green coffee.18 The legal limit therefore applies to the roaster’s product, not to the green lot as traded (our reading). The Codex code allows out-sorted defects back into the food chain only if a representative sampling plan and direct OTA analysis show them to be acceptable.1 The European standard method EN 14132 uses immunoaffinity clean-up and high-performance liquid chromatography (HPLC). It is validated for roasted coffee at 0.2–5.5 µg/kg.19 Official sampling plans and the toxin itself are covered in Ochratoxin A.

Pesticide residues. Residue testing on green coffee is described in a 2022 review as difficult. Coffee is a complex matrix; caffeine gives a large, broad peak that can hide residues in gas chromatography, and lipids must be removed in clean-up.20 Liquid chromatography is used where gas chromatography reaches its limits.20 Maximum residue levels are covered in Pesticide residues.

Refusal at the border. Under the GCA guarantee clause, coffee refused admission at the port of destination for a violation of government laws is subject to replacement.16 Border checks are described in Import and customs.

Food-safety management#

QC on green coffee sits inside a food-safety system. In the EU, the food business operator carries primary responsibility for food safety.21 Regulation (EC) No 852/2004 requires operators after primary production to keep permanent procedures based on the principles of hazard analysis and critical control points (HACCP).21 The principles include identifying hazards, setting critical limits that separate acceptable from unacceptable, corrective actions, verification and records.21 Primary production falls under separate general hygiene provisions instead.21

For exporters, the ITC guide states that controls must be documented in a HACCP plan, and that discrepancies and the actions taken to correct them must be recorded.23 For example, a moisture limit at receipt could serve as a critical limit, and segregation of a failed lot as the corrective action (our example, not taken from a source). The Codex code asks every stakeholder to refuse suspect coffee and to set up a rapid assessment of incoming coffee.1

Acceptance, claims and failed lots#

Against what. QC compares a result with the contract. The GCA contract advises that the maximum allowable moisture should be part of the quality description.16 When an arrival sample is compared with the sample sold on, due consideration is given to dryage and a reasonable change in colour.16 Some variation between pre-shipment and arrival results is therefore expected; how much the contract tolerates is not set as a number in the sources consulted.

Export targets. The ICO resolution of 2004 marks shipments that miss its targets: “XD” for defects, “XM” for moisture, “XDM” for both.14 If coffee marked as compliant fails in trade, importing members may notify the ICO.14

Remedies. Under the ESCC, a quality difference gives an allowance, which may include costs; unsound or radically different coffee may be invoiced back.15 Under GCA shipment terms, quality is a matter of allowance only.16 Procedures, panels and awards are explained in Arbitration and Green coffee contracts.

Records, lot identity and instrument checks#

Records. EU law requires documents and records commensurate with the nature and size of the business, and up-to-date documents describing the procedures.21 The Codex code asks warehouses to record the initial condition and age of the stocks they receive.1

Lot identity in the warehouse. The Codex code has coffee types kept separate under a labelling system.1 ISO 4072 keeps the rest of each bulk sample in a labelled container until the buyer accepts the consignment; see Samples in the trade.2 Whole-chain systems are covered in Traceability.

Instrument checks. The Codex code asks for moisture equipment to be cross-checked and calibrated once a year before harvest against ISO 6673.1 The ITC guide asks for meters to be recalibrated at the start of each season.23 ISO 24115 gives the procedure, including the correction for bean temperature and the expanded uncertainty.6

Monitoring stored lots#

Stored coffee is re-tested because it changes. The Codex code asks for strict control of humidity in long-term storage.1 A university extension guide advises checking the moisture of stored coffee at regular intervals, and more often where the storage air is not controlled.7

Moisture alone does not show ageing. A 2023 storage study measured water activity, free fatty acids and volatile compounds in green coffee over 12 months.22 The authors call free fatty acids one of the basic quality parameters of green coffee in storage. They found gas chromatography with mass spectrometry suitable for following ageing through volatile compounds.22 No source consulted for this entry sets an interval for re-cupping stored lots. The effects of time and temperature are described in Green coffee storage.

Open questions#

  • Current ISO texts. ISO 6673 and ISO 4149 appeared in new editions in November 2025; whether the oven parameters, precision data or examination methods changed could not be checked.5,10
  • Meter agreement in trade. Apart from the 2005 trial, no study consulted for this entry compares the moisture meters used by exporters and importers on the same lots.17
  • Tolerances between pre-shipment and arrival. The contracts allow for dryage and a reasonable change in colour but set no numeric tolerance in the sources consulted.16
  • Water activity in acceptance. Codex gives a ceiling; the SCA CVA does not require the test. No contract consulted sets a water activity limit.1,11
  • Re-test intervals. No standard consulted sets how often stored lots should be re-cupped.

Key documents#

ISO, 2003 – Green coffee: loss in mass at 105 °C (ISO 6673). The reference moisture method of the trade, with interlaboratory precision data from 13 laboratories. Two correct laboratories may differ by up to about one percentage point; a third edition appeared in 2025.

ISO 6673:2003 · Preview · ISO 6673:2025 catalogue

ISO, 2012 – Calibration of moisture meters for green coffee (ISO 24115). Sets out how to adjust a meter against at least five reference samples measured by ISO 6673, correct for bean temperature and state an expanded uncertainty.

ISO 24115:2012 · ISO catalogue

Palácios Cabrera and Souza, 2005 – Moisture methods in simulated sea transport. Measured the same hulled arabica by oven, capacitance meter and weight gain in three mini-containers. The meter read about two points above the oven throughout, while both showed only a small gain.

ITAL analysis report MB-4583-6596/05, FAO coffee project Annex C.10 · FAO PDF

Błaszkiewicz et al., 2023 – Storage conditions and quality parameters. Stored washed and natural green coffee at −10, 10 and 20 °C for a year and followed water activity, free fatty acids and volatile compounds. It proposes free fatty acids and volatile profiles as markers of ageing.

Scientific Reports 13, 6447 · doi:10.1038/s41598-023-33609-x

Share or cite this entry

Change log

  • – The University of Hawai‘i extension guide EN-3 (source 7) is now Tier B. Its advice to check stored coffee 'once a month' rested on it alone and now reads 'at regular intervals'; its other uses (how meters work, drift, calibration, repeatability, re-checks in storage) carry no numbers and stay, attributed. Reason: Tier decision of 8 Nov 2026: state university extension fact sheets without stated review are Tier B, and a Tier B source never carries a number alone.

Sources

  1. ACodex Alimentarius Commission (FAO/WHO) (2009). Code of Practice for the Prevention and Reduction of Ochratoxin A Contamination in Coffee (CAC/RCP 69-2009). Codex Alimentarius.Quoted passage: a recommendation; International code of practice for the whole coffee chain, 2009..
  2. AWinston, E.; Op de Laak, J.; Marsh, T.; Lempke, H.; Chapman, K. (2005). Arabica coffee manual for Lao-PDR, Chapter 8: Quality and export standards. FAO Regional Office for Asia and the Pacific, Bangkok.Quoted passage: a definition; Reproduction of ISO 4072:1982, sampling of green coffee in bags..
  3. AInternational Organization for Standardization (ISO/TC 34/SC 15) (2011). ISO 6666:2011 Coffee sampling — Triers for green coffee or raw coffee and parchment coffee. ISO.Quoted passage: a description; ISO catalogue abstract of ISO 6666:2011..
  4. AInternational Organization for Standardization (2003). ISO 6673:2003 Green coffee — Determination of loss in mass at 105 °C. ISO.Quoted passage: data; International standard method and its interlaboratory precision data, 2003 edition..
  5. AInternational Organization for Standardization (2025). ISO 6673:2025 Green coffee — Determination of loss in mass at 105 °C. ISO.
  6. AInternational Organization for Standardization (ISO/TC 34/SC 15) (2012). ISO 24115:2012 Green coffee — Procedure for calibration of moisture meters — Routine method. ISO.Quoted passage: a definition; International standard for calibrating moisture meters for green coffee against ISO 6673; publisher's preview (clauses 1–7, Annex A)..
  7. BGautz, L. D.; Smith, V. E.; Bittenbender, H. C. (2008). Measuring Coffee Bean Moisture Content (Engineer's Notebook EN-3). College of Tropical Agriculture and Human Resources, University of Hawai'i at Mānoa.Quoted passage: a recommendation; Extension guide for coffee growers and millers in Hawai'i, 2008..
  8. AInternational Organization for Standardization (ISO/TC 34) (2017). ISO 18787:2017 Foodstuffs — Determination of water activity. ISO.Quoted passage: a description; ISO catalogue abstract of ISO 18787:2017..
  9. AInternational Organization for Standardization (ISO/TC 34/SC 15) (1995). ISO 6669:1995 Green and roasted coffee — Determination of free-flow bulk density of whole beans (Routine method). ISO (preview pages via ANSI Webstore).
  10. AInternational Organization for Standardization (ISO/TC 34/SC 15) (2025). ISO 4149:2025 Green coffee — Olfactory and visual examination and determination of foreign matter and defects. ISO.Quoted passage: a description; ISO catalogue abstract of ISO 4149:2025..
  11. A/BSpecialty Coffee Association (writing team Fernández-Alduenda, M.; Ionescu, K. E.; Giuliano, P.; Rugolo, J.; Delrue, R.) (2024). A System to Assess Coffee Value: Understanding the Specialty Coffee Association’s Coffee Value Assessment (June 2024). Specialty Coffee Association.Quoted passage: a definition; SCA Coffee Value Assessment, physical assessment section; applies to washed arabica..
  12. A/BSpecialty Coffee Association (2024). SCA Standard 102-2024 Coffee Value Assessment: Sample Preparation and Tasting Mechanics. Specialty Coffee Association.Quoted passage: a definition; SCA standard for sample roasting and cupping mechanics, 2024..
  13. AInternational Organization for Standardization (ISO/TC 34/SC 15) (2008). ISO 6668:2008 Green coffee — Preparation of samples for use in sensory analysis. ISO.Quoted passage: a description; ISO catalogue abstract of ISO 6668:2008..
  14. AInternational Coffee Council (2004). Resolution Number 420: Coffee Quality-Improvement Programme – Modifications. International Coffee Organization, 90th Session, London.
  15. A/BEuropean Coffee Federation (2018). European Standard Contract for Coffee (ESCC), 2018 Edition. European Coffee Federation, Brussels (copy hosted by the Comitato Associazioni Italiane Caffè, CAIC).Quoted passage: a definition; Standard contract form of the European Coffee Federation, 2018; applies where the parties adopt it..
  16. A/BGreen Coffee Association (2021). Contract Terms and Conditions (effective May 1, 2002, as amended to September 27, 2021). Green Coffee Association, Inc., New York.Quoted passage: a definition; Standard contract form of the Green Coffee Association, New York, as amended to 27 September 2021; applies where the parties adopt it..
  17. APalácios Cabrera, H. A.; Souza, J. L. de (Instituto de Tecnologia de Alimentos, ITAL) (2005). Analysis Report MB-4583-6596/05: coffee in mini-containers during simulated maritime transport (FAO coffee project, Annex C.10). FAO / Instituto de Tecnologia de Alimentos (ITAL), Brazil.Quoted passage: data; Simulated maritime transport in three mini-containers, hulled arabica, Brazil, 2005; three trials of 15 days..
  18. AEuropean Commission (2025). Commission Regulation (EU) 2023/915 on maximum levels for certain contaminants in food (consolidated text, 01.01.2025), Annex I, section 1.2. EUR-Lex.
  19. AEuropean Committee for Standardization (CEN) (2009). EVS-EN 14132:2009 Foodstuffs – Determination of ochratoxin A in barley and roasted coffee – HPLC method with immunoaffinity column clean-up. Estonian Centre for Standardisation and Accreditation (catalogue page).
  20. AMerhi, A.; Kordahi, R.; Hassan, H. F. (2022). A review on the pesticides in coffee: Usage, health effects, detection, and mitigation. Frontiers in Public Health 10, 1004570. doi:10.3389/fpubh.2022.1004570 · other copiesQuoted passage: a description; Narrative review of pesticide use, residues and detection in coffee, 2022..
  21. AEuropean Parliament and Council of the European Union (2004). Regulation (EC) No 852/2004 of the European Parliament and of the Council of 29 April 2004 on the hygiene of foodstuffs. EUR-Lex (original text as published).
  22. ABłaszkiewicz, J.; Nowakowska-Bogdan, E.; Barabosz, K.; Kulesza, R.; Dresler, E.; Woszczyński, P.; Biłos, Ł.; Matuszek, D. B.; Szkutnik, K. (2023). Effect of green and roasted coffee storage conditions on selected characteristic quality parameters. Scientific Reports 13, 6447. doi:10.1038/s41598-023-33609-x · other copiesQuoted passage: the authors’ own result; Washed and natural green coffee stored at −10, 10 and 20 °C for up to 12 months, Poland..
  23. AInternational Trade Centre (ITC) (2011). The Coffee Exporter's Guide, Third Edition. International Trade Centre (UNCTAD/WTO), Geneva.Quoted passage: a recommendation; Trade guide for exporters in producing countries, 2011..

Tier A · authoritative · B · trade and expert · C · general. Supporting quotes for every source are in the data version of this entry. If a publisher’s site refuses access, try the doi link or “other copies”.

The literature for this entry was last searched on 10 Nov 2026. A statement that no source consulted for this entry shows something refers to the sources above; newer or missing work may exist.

Suggest a change

On Green coffee quality control. Tell us what you would change and why. A source that supports it helps most.